Eight free practice questions on BC Electrical Code rules and the TSBC notices that interpret them, for Unit C (BC Electrical Code Rules) of the TicketPrep bank for the BC electrical Field Safety Representative (FSR) certificate of qualification exam, Classes A, B and C. Technical Safety BC sets and delivers the exam. These are original questions written by TicketPrep from the BC statutes, the Technical Safety BC directives and bulletins and the Canadian Electrical Code Rule numbers, not questions from the exam. Each has four options and one correct answer, as every question in our bank does. Answer each one before opening the explanation. No account, no email.
01The questions
-
At a winery, the FSR reviews four tasks a crew wants to do energized. Under D-EL 2016-02 and TSBC's bulletin IB-EL 2013-01, which one could be shown to be not feasible de-energized?
- Replacing an office receptacle without turning off the office lights
- Adding a breaker while the tasting room is open, to avoid overtime
- Tracing an intermittent fault in a running chiller's controls
- Retorquing service lugs, as pulling the meter costs a utility fee
Show the answer
C. Correct. IB-EL 2013-01 lists troubleshooting, testing and diagnostics that operational limits make impossible with the equipment off as cases where disconnection may be shown not feasible; a fault that appears only while the chiller runs fits. Those doing it must be able to document why, for TSBC and WorkSafeBC on request, and work under WorkSafeBC rules (Rule 2-304 as D-EL 2016-02 reads it).
Why not the others
A. Keeping the lights on is a convenience, not infeasibility. The receptacle's own branch circuit can be switched off, and D-EL 2016-02 requires the work to be done de-energized.
B. Avoiding overtime is a cost reason, and IB-EL 2013-01 says cost and inconvenience never justify removing or bypassing protective provisions. Under D-EL 2016-02 the breaker is added with the panel de-energized, after hours if need be.
D. A supply authority charge for pulling the meter is a cost, which TSBC's bulletin rejects as a reason for live work. Service lugs are worked on de-energized, arranged with the supply authority.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rule 2-304; TSBC D-EL 2016-02, IB-EL 2013-01, IB-EL 2016-05
-
An FSR's crew will run rigid PVC conduit underground from a house to a detached shop on a rural lot. The native soil is coarse gravel, so the owner has a backfill specification from a professional engineer in good standing in BC instead of screened sand. Under TSBC's bulletin IB-EL 2020-01, what must the FSR do?
- Name the engineered option on the permit and file the specification before the concealment request
- Apply for a variance before backfilling, as any fill other than screened sand departs from Rule 12-012
- Keep the specification on site and show it to the safety officer at the final inspection
- Attach the specification to the final declaration once the trench has been backfilled
Show the answer
A. Correct. IB-EL 2020-01 says that when an option other than plain Rule 12-012 compliance is chosen, the FSR states it when taking out the permit (or in the remarks of the concealment request, with the permit's work description revised), and an engineered specification must reach the authority before the concealment inspection is requested (Rule 2-014). The bulletin also makes it the FSR's job to show the work complies.
Why not the others
B. A variance is needed only for a method outside the bulletin's three options. IB-EL 2020-01 lists an engineered specification from a qualified professional in good standing in BC as one of the acceptable options, so no variance is required for it.
C. Too late. The trench is backfilled long before the final inspection. IB-EL 2020-01 wants the engineered specification submitted before an inspection is requested for concealment of the raceway, so it can be checked while the work is still open.
D. A declaration after concealment does not meet the bulletin. IB-EL 2020-01 requires the chosen option to be named on the permit (or in the concealment request) and the engineered specification to be filed before the concealment inspection is requested.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rules 12-012, 2-014; TSBC IB-EL 2020-01
-
A two-storey office building has six tenant units. The design groups every tenant's branch-circuit panelboard in one shared electrical room on the ground floor, away from the units. Under Directive D-EL 2016-07, how should the FSR treat this?
- Reject it, as each panel belongs in the occupancy its circuits supply
- Accept it, since the Section 0 definition names no particular occupancy
- Accept it, since 14-106 wants overcurrent devices grouped where practicable
- Accept it, if each panel is labelled with the unit and circuits it serves
Show the answer
A. Correct. D-EL 2016-07 (part A, Rule 14-106) interprets branch-circuit overcurrent devices outside dwelling units as readily accessible when they sit inside the occupancy their circuits serve, so each tenant's panel goes in that tenant's unit. The directive aims to give occupants ready access to the devices controlling their equipment.
Why not the others
B. That is the bare definition, and D-EL 2016-07 itself notes it names no occupancy. The binding BC reading is that, outside dwelling units, branch-circuit overcurrent devices are readily accessible when located within the occupancy they supply.
C. Grouping is asked for only where practicable and never overrides ready access. D-EL 2016-07 reads ready access for branch-circuit devices outside dwelling units as being within the occupancy the circuits supply.
D. Labelling is needed anyway (Rule 2-100 3)), but it does not give the tenant ready access. D-EL 2016-07 places branch-circuit overcurrent devices outside dwelling units within the occupancy they supply.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rules 14-106, 2-100; TSBC D-EL 2016-07
-
An owner is adding a secondary suite to a single dwelling. Under Rule 26-602 as D-EL 2016-01 and IB-EL 2023-03 read it, which supply arrangement requires a panelboard for the suite?
- One meter, with one panel anywhere in the house serving both units
- One meter, with a subpanel for the suite fed from the main panel
- A duplex meter base, with the suite on a meter of its own
- A dual-lug meter base on one meter, feeding a panel for each unit
Show the answer
C. Correct. Once the suite is individually metered, the 26-602 1) b) exemption is lost (both conditions are needed), so the suite needs its own panelboard, and 26-602 2) then requires a single protected supply that can be disconnected without disconnecting the other unit. IB-EL 2023-03 adds that the code does not require the suite to be metered: that is the installer's choice.
Why not the others
A. With no separate meter, the suite meets both conditions of 26-602 1) b) (subdivision of a single dwelling, not individually metered), so no suite panelboard is required; IB-EL 2023-03 calls this layout compliant.
B. IB-EL 2023-03 accepts this but notes the subpanel is a convenience, not a requirement: the suite is not individually metered, so 26-602 1) b) exempts it.
D. One meter still means the suite is not individually metered. IB-EL 2023-03 says the second panel here is not required by 26-602 1), and 26-602 2) does not apply.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rule 26-602; TSBC D-EL 2016-01, IB-EL 2023-03
-
A licensed electrical contractor is wiring a new propane container-filling station at a farm supply store. The owner asks the FSR whether the hazardous areas must be set by a classification study prepared under Rule 18-004 1) to 4). What does Rule 18-004 allow for this installation?
- It may be classified by the zone extents Section 20 sets for propane filling
- It needs a study signed by a professional engineer before any permit is issued
- It needs no classification, as the filling is done outdoors in open air
- It is classified by the safety officer at the rough-in inspection
Show the answer
A. Correct. Rule 18-004 5) lets an installation within Section 20's scope be classified in accordance with Section 20, and Section 20 covers propane container filling (Rules 20-030 to 20-042). Section 20's prescribed zones then serve as the classification; a site-specific study is the route for facilities Section 20 does not cover.
Why not the others
B. Rule 18-004 contains no engineer's-seal requirement. In BC, TSBC's bulletin IB-EL 2016-01 says only that the authority may require professionally signed designs; for a Section 20 installation, Rule 18-004 5) lets Section 20 itself classify it.
C. Open air does not take a propane filling area out of the hazardous categories: Section 20 (Rules 20-030 to 20-042) covers the locations where propane is transferred to portable containers, outdoors included, and Rule 18-004 5) lets those Section 20 rules serve as the classification rather than removing it.
D. A safety officer inspects against the classification; Rule 18-004 places classification on qualified persons and, for Section 20 installations, allows Section 20's zones to be used. The designer's work must exist before the wiring is chosen.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rules 18-004, 20-000
-
A new house is close to completion and drywallers are using its permanent receptacles for power: the 5-15R receptacles in a basement bedroom (no GFCI required there by the general rules) and a 5-15R on the rear deck, outdoors, 1 m above grade. Under D-EL 2016-03 and the code, which of them need Class A GFCI protection?
- All of them, under Rule 76-016, while they power construction
- Only the deck receptacle, under Rule 26-704 2)
- None of them, because permanent wiring is outside Section 76
- Only the bedroom receptacles, as they are used indoors by the trades
Show the answer
B. Correct. D-EL 2016-03 makes Section 76, and so the 76-016 GFCI rule, apply only to temporary installations; permanent receptacles used during construction follow the general rules. Those leave the bedroom receptacles without GFCI, while 26-704 2) requires Class A GFCI on outdoor 5-15R and 5-20R receptacles within 2.5 m of finished grade.
Why not the others
A. D-EL 2016-03 limits 76-016 to receptacles installed specifically for temporary power. Permanent receptacles used for construction are outside Section 76, so 76-016 adds nothing to the bedroom receptacles.
C. Being outside Section 76 does not exempt a receptacle from the general rules. The deck receptacle is outdoors within 2.5 m of grade, so Rule 26-704 2) still calls for Class A GFCI protection.
D. Indoor use by trades does not trigger GFCI protection on permanent receptacles (D-EL 2016-03). The outdoor deck receptacle is the one the general rules catch, through 26-704 2).
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rules 76-000, 76-016, 26-704; TSBC D-EL 2016-03, IB-EL 2011-01
-
A new switchboard in a strata building's electrical room has a 2000 A nameplate rating, and its largest overcurrent device is an 800 A main breaker. A worker at the far end must pass the board to reach the only door. What do Rules 2-310 and 2-306 3) require?
- Arc-energy means only, as 2-310 turns on the main
- Neither rule, as both turn on the 800 A main
- Egress or 1.5 m of working space, plus arc-energy means
- Egress or 1.5 m of working space; no arc-energy means
Show the answer
D. Correct. Rule 2-310 2) turns on the equipment's nameplate rating (1200 A or more), and TSBC's bulletin IB-EL 2016-05 stresses that a smaller main does not change that: arrange the room so nobody passes the failure point to leave, and only if that cannot be done raise the working space to 1.5 m. Rule 2-306 3), new in 2024, needs an arc-energy reduction means only where an overcurrent device is rated 1200 A or more; the 800 A main is not.
Why not the others
A. This reverses the two triggers. Rule 2-310 2) follows the 2000 A nameplate rating, so it applies; Rule 2-306 3) follows the overcurrent device rating, so with an 800 A main it does not.
B. Only Rule 2-306 3) turns on the overcurrent device rating. Rule 2-310 2) looks at the equipment's nameplate rating, so this 2000 A switchboard needs a safe exit route or 1.5 m of working space even with an 800 A main.
C. The arc-energy reduction of Rule 2-306 3) applies where an overcurrent device is rated 1200 A or more. With an 800 A main as the largest device it does not apply here, although the 2-310 egress rule does.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rules 2-306, 2-308, 2-310; TSBC IB-EL 2016-05
-
A 347/600 V three-phase, 4-wire feeder in a warehouse supplies only metal-halide high-bay luminaires connected line to neutral. Under Rule 4-018 and TSBC's bulletin IB-EL 2016-06, how are the neutral and the conductor count treated?
- Neutral at 70 % above 200 A; four conductors counted
- Full-size neutral; three current-carrying conductors
- Reduced neutral; three current-carrying conductors
- Full-size neutral; four current-carrying conductors
Show the answer
D. Correct. Rule 4-018 2) a) allows no neutral reduction for the part of the load that is electric-discharge lighting, and IB-EL 2016-06 explains that third-harmonic current can make the neutral current as large as the phase current, so a three-phase 4-wire circuit feeding such lighting is counted as four current-carrying conductors when derating under Rule 4-004.
Why not the others
A. The 70 % factor of Rule 4-018 2) b) applies to unbalanced load over 200 A only where item a) does not; discharge lighting is excluded from any reduction.
B. Not counting the neutral fits a balanced circuit whose neutral carries only unbalance (Rule 4-004 3)). With discharge lighting the third harmonics add in the neutral, so IB-EL 2016-06 counts four current-carrying conductors.
C. A neutral may normally be sized for the unbalanced load, but Rule 4-018 2) a) bars any reduction for discharge lighting, and the neutral is counted for derating.
Source: TSBC FSR exam, Code (our Unit C: BC Electrical Code Rules); CEC Rules 4-018, 4-004; TSBC IB-EL 2016-06
02Answer key
| Question | Answer | Our objective |
|---|---|---|
| Q1 | C | Objective C-1 |
| Q2 | A | Objective C-4 |
| Q3 | A | Objective C-5 |
| Q4 | C | Objective C-6 |
| Q5 | A | Objective C-7 |
| Q6 | B | Objective C-9 |
| Q7 | D | Objective C-1 |
| Q8 | D | Objective C-2 |
03What Unit C covers
Unit C is the code rules half of the Code part: the Canadian Electrical Code, Part I, 2024 edition, which has been the B.C. Electrical Code since March 4, 2025, read with the binding Technical Safety BC directives and the code bulletins. Our objectives run section by section from the general rules through conductors and services, grounding and bonding, wiring methods, protection and control, Section 26, hazardous locations, motors and heating, and the special sections. BC adopted the 2024 code with no deviations, so the BC layer comes through the directives: they decide how a Rule is applied here, and the questions often turn on that reading. Section 36 and high voltage are Class A only; our bank keeps those questions in their own set, outside the Class B and C mock.
Technical Safety BC gives each of the Class A, B and C exams 60 multiple-choice questions in 3.5 hours, open book, with a 35 per cent focus on the Act, Regulations and Directives and a 65 per cent focus on the Code, and a pass mark of 70 per cent. It publishes nothing finer than that split. Our four units, and our mock's draw of 39 Code questions, 18 of them from Unit C, are ours: 21 and 39 of 60 is our reading of the 35 / 65 split, divided between the units by the size of each. The ten objectives below are TicketPrep's own grouping, and the right-hand column is how many questions our bank holds on each, Standard and Advanced together, not a count from the exam. Objective C-10, Section 36 and high voltage with directive D-E3 090313 1, is examined on Class A only. Our bank keeps its 30 questions in a set of their own, outside the Class B and C mock, and has no questions on CSA C22.3 No. 1, Overhead Systems, which Class A also examines.
| Our objective | In our bank |
|---|---|
| C-1 Section 0 definitions and Section 2 general rules, with D-EL 2016-02 | 14 |
| C-2 Section 4 conductors and Section 6 services, with the BC service notices | 20 |
| C-3 Section 10 grounding and bonding rules | 13 |
| C-4 Section 12 wiring methods, with the BC underground and building-type bulletins | 15 |
| C-5 Section 14 protection and control, with D-EL 2016-07, and Section 16 | 13 |
| C-6 Section 26 installation of equipment, with D-EL 2016-01 and the suite bulletin | 17 |
| C-7 Sections 18, 20, 22 and 24: hazardous, corrosive and patient-care locations | 9 |
| C-8 Section 8 rules, Section 28 motor rules, and Sections 30, 32, 46 and 62 | 13 |
| C-9 Sections 64 to 86 and the other special sections, with D-EL 2016-03 | 16 |
| C-10 Section 36 and high voltage (Class A only; practised as its own set, not in the mock) | 30 |
04What the questions turn on
De-energized unless shown not feasible
Directive D-EL 2016-02 reads Rule 2-304 as requiring electrical work to be done de-energized unless that is shown not to be feasible, and bulletin IB-EL 2013-01 gives the cases: mostly testing, troubleshooting and diagnostics that cannot be done with the equipment off. Working space follows the equipment's rating too: Rule 2-310 turns on the nameplate rating, not on the size of the main breaker.
Readily accessible means in the occupancy
Directive D-EL 2016-07 treats branch-circuit overcurrent devices outside dwelling units as readily accessible under Rule 14-106 when they sit inside the occupancy their circuits serve. A design that gathers every tenant's panel in one shared room fails that reading. For dwellings, directive D-EL 2016-01 and bulletin IB-EL 2023-03 decide when a secondary suite needs its own panelboard under Rule 26-602: separate metering is one of the triggers.
Temporary or permanent decides the rule
Directive D-EL 2016-03 applies Section 76, and its GFCI rule, only to temporary installations. Permanent receptacles that trades use during construction follow the general rules, so an outdoor receptacle near grade needs Class A GFCI protection under Section 26 while a bedroom receptacle does not. Electric-discharge lighting works the same way through Section 4: a neutral feeding it is not reduced, and on a three-phase, 4-wire circuit it counts as a current-carrying conductor.
Show the option before the inspection
Bulletin IB-EL 2020-01 makes the FSR responsible for showing that underground work complies. When an option other than the plain Rule 12-012 method is chosen, such as engineered backfill, the FSR names it on the permit and files the specification before the concealment inspection is requested. Hazardous locations have a similar shortcut: Rule 18-004 lets an installation that Section 20 covers, such as propane container filling, be classified by that Section's zones.
05The other units
Technical Safety BC sets no minimum score for either part, only the 70 per cent pass mark on the whole exam, so every unit's marks count toward it. Each of our four units has its own page of free questions:
The BC FSR practice exam page describes the full question bank. Writing a master electrician exam in another province as well? See the Alberta Master Electrician practice test or the Ontario Master Electrician practice test; for the trade exam itself, the 309A Construction Electrician practice exam. More free questions for every exam we cover: free practice questions. How these questions are written and checked: how our questions are made. Found a mistake? Tell us and we will fix it. TicketPrep is not affiliated with Technical Safety BC or CSA Group. The Canadian Electrical Code is cited by Rule number only and never reproduced; BC statutes are paraphrased, and Technical Safety BC directives and bulletins are cited by number and explained in our own words.